Metal Weight Calculator

The weight in kilograms and pounds of a metal plate, bar, pipe, tube or angle from its dimensions, length and quantity.

Density is shown in kilograms per cubic metre.

mm

mm

m

Per kilogram in metric, per pound in inches and feet.

Weight

233.68 kg

or 515.17 lb

Weight of one piece
233.68 kg
Pieces
1
Weight per metre
95.77 kg/m
Weight per foot
64.354 lb/ft
Total in kilograms
233.68 kg
Total in pounds
515.17 lb
Total in tonnes
0.2337 t

One piece of this mild steel weighs 233.68 kg, which is 95.77 kg per metre.

Add this calculator to your website

Free to use on any site or blog. Paste this code where you want the calculator to appear. It stays up to date, needs no account, and keeps your visitors' numbers in their own browser.

Preview

How it works

The weight of a piece of metal is its volume times its density. For a bar or plate that is the area of the cross-section, times the length, times the density. The calculator works out the cross-section for the shape you pick, then multiplies by the length and the density of the metal.

Mild steel is 7,850 kilograms per cubic metre, stainless 304 is 7,930, aluminium is 2,700 and copper is 8,960. A steel plate 1,220 mm wide, 2,440 mm long and 10 mm thick therefore has a volume of 0.02977 cubic metres and weighs about 233.7 kg.

For a TMT or rebar, choose Round bar and enter the diameter in millimetres. A bar weighs about the diameter squared divided by 162.2 kilograms per metre, so a 12 mm bar is 0.888 kg per metre and a 12 metre length is about 10.65 kg. The calculator gives the same figure without the shortcut.

Hollow shapes remove the inside from the outside. A pipe is the full circle of the outside diameter minus the circle of the hole. A square or rectangular tube is the outer rectangle minus the inner one, and the inner size is the outer size less twice the wall. Angles are two legs that share a corner, so the calculator adds both legs and takes off the corner once.

Check it by hand: weight is volume × density. A steel plate 1,220 mm wide, 10 mm thick and 2.44 m long has a volume of 1.22 × 0.01 × 2.44 = 0.029768 m³. At 7,850 kg/m³ that is 0.029768 × 7,850 = 233.68 kg. One metre of the same plate is 1.22 × 0.01 × 7,850 = 95.77 kg. In pounds, 233.68 × 2.20462 = 515.17 lb.

Weight = cross-section area × length × density
Plate or flat: width × thickness
Round bar: π × d² ÷ 4    Square bar: side²    Hexagon: 0.866 × (across flats)²
Pipe: π ÷ 4 × (D² − (D − 2t)²)
Square tube: a² − (a − 2t)²    Rectangular tube: w × h − (w − 2t) × (h − 2t)
Angle: t × (leg A + leg B − t)
Steel 7,850 kg/m³    Aluminium 2,700    Copper 8,960

Worked example

A mild steel plate 1,220 mm wide, 10 mm thick and 2.44 m long has a cross-section of 0.01220 m² and a volume of 0.029768 m³. At 7,850 kg/m³ it weighs 233.7 kg, or 515.2 lb.

Ten pieces weigh 2,337 kg, or 2.337 tonnes. Enter a price per kilogram to see the cost.

Good to know

  • The calculator uses the nominal size. Rolled steel can be a little over or under, and plates are often a small percentage heavier than the formula because of rolling tolerance.
  • Angles are worked out as two flat legs and ignore the rounded inner corner and the tapered legs of some sections. Real angles are within a few percent of the figure. Use the maker's table when you need an exact value.
  • Channels, beams and other rolled sections have tapered flanges and are not covered. Use the weight per metre from the maker's table for these.
  • Galvanised (GI) sheet carries a thin zinc coating, which adds only a tiny amount to the weight. The steel density is used for it.

Questions people ask

How do I calculate the weight of an MS plate?

Multiply length, width and thickness in metres to get the volume, then multiply by 7,850 kg per cubic metre. A plate of 2.44 m by 1.22 m and 10 mm thick weighs 2.44 × 1.22 × 0.01 × 7850 = 233.7 kg.

How much does a TMT bar weigh per metre?

About the diameter in mm squared divided by 162.2. A 8 mm bar is 0.395 kg per metre, 10 mm is 0.617, 12 mm is 0.888, 16 mm is 1.578, 20 mm is 2.466 and 25 mm is 3.853.

What is the density of steel?

Mild and carbon steel is about 7,850 kg per cubic metre, which is 0.2836 pounds per cubic inch. Stainless steel is a little denser at about 7,930 to 8,000.

How do I find the weight of a steel pipe?

Subtract the inside circle from the outside circle, multiply by the length and by 7,850. A pipe of 60 mm outside diameter with a 3 mm wall is about 4.2 kg per metre.

Is the weight of stainless steel different from mild steel?

Slightly. Stainless 304 is about 1% heavier and 316 about 2% heavier than mild steel for the same size, so the difference is small but real on large orders.

How much does a steel plate 1 m by 1 m and 10 mm thick weigh?

1 × 1 × 0.01 = 0.01 m³, and 0.01 × 7,850 = 78.5 kg.

Part of the guide: Building material calculators: concrete, blocks, bricks, flooring and more, Roof, stair, deck and structure calculators

Formulas and text last checked on 6 October 2026. Everything is calculated in your browser, so nothing you enter is sent or stored. Spotted a mistake? Tell us and we will fix it.