How it works
A pool holds its surface area times its average depth. The calculator finds the surface area for the shape you pick, works out the average depth from the shallow and deep ends, and multiplies the two. The volume is then shown in US gallons, imperial gallons, litres, cubic metres and cubic feet.
A rectangle is length times width. A round pool is π times the radius squared. An oval is π ÷ 4 times the length times the width. A kidney pool is measured the way pool builders do it, by adding the widths of its two lobes, multiplying by the length and by 0.45.
Most pools slope from the shallow end to the deep end. If the floor slopes evenly, the average depth is half of the sum of the two depths. If your pool has a flat shallow area and a sudden drop, work out each section separately and add the results. For a pool of constant depth, enter the same depth in both boxes.
Measure the depth to the water line, not to the top of the wall, since the water usually stands a few inches below the edge. About 7.48 US gallons fill one cubic foot, and 1,000 litres fill one cubic metre.
Check it by hand: length × width × average depth gives the volume in cubic feet, and one cubic foot is 7.48 US gallons. For a 20 by 10 foot pool that is 3 feet deep at one end and 6 feet at the other, the average depth is 4.5 feet, so 20 × 10 × 4.5 = 900 cubic feet. Then 900 × 7.48 = 6,732 gallons.
Volume = surface area × average depth Average depth = (shallow depth + deep depth) ÷ 2 Rectangle: length × width Round: π × diameter² ÷ 4 Oval: π ÷ 4 × length × width Kidney: (A + B) × length × 0.45 1 ft³ = 7.4805 US gallons = 28.317 litres
Worked example
A rectangular pool 20 feet long and 10 feet wide has a surface of 200 square feet. It slopes from 3 feet to 6 feet, so the average depth is 4.5 feet.
The volume is 200 × 4.5 = 900 cubic feet, which is 6,732 US gallons, 5,606 imperial gallons or 25,485 litres.
Good to know
- The result is an estimate. Steps, benches, a sudden drop or a rounded corner change the real volume by a few percent. For a chemical dose, be a little careful and add up the sections one by one.
- The kidney formula is a trade rule of thumb, not an exact shape. Kidney and free-form pools can differ from it by 5 to 10%.
- Water level matters. Measure the depth to where the water actually stands, because a pool that is filled to the tile line has less water than the shell can hold.
Questions people ask
How do I calculate how many gallons are in my pool?
Multiply length by width by average depth in feet to get cubic feet, then multiply by 7.48. A pool of 20 by 10 feet with an average depth of 4.5 feet holds about 6,732 US gallons.
How many litres are in a swimming pool?
Multiply length by width by average depth in metres to get cubic metres, then multiply by 1,000. A pool of 6 by 3 metres with an average depth of 1.5 metres holds 27,000 litres.
How do I find the average depth of a pool?
Add the shallow end depth and the deep end depth and divide by 2. This works when the floor slopes evenly. If there is a flat area and then a steep drop, work out the parts separately.
How many gallons is a round pool?
Use π × (diameter ÷ 2)² × depth × 7.48. A round pool 15 feet across and 4 feet deep holds about 5,288 gallons.
How many gallons is a 20 by 10 foot pool?
A rectangular pool 20 by 10 feet that slopes from 3 feet to 6 feet deep holds about 6,732 US gallons, or 25,485 litres.
Part of the guide: Heating, cooling and water calculators: BTU, pipes, tanks, pumps and pools