Heating, cooling and water calculators: BTU, pipes, tanks, pumps and pools

Size air conditioners, furnaces, radiators, ducts and water heaters, and work out tank, pool, pipe, pump and rainwater volumes.

Heating, cooling and water systems are sized from a few inputs: the size of the space, how much heat or water it needs, and the margin to allow. The tools below give a first estimate with the working shown, so you can talk to a supplier or installer with real numbers.

They are estimates for planning. Final sizing depends on insulation, climate, local code and the equipment, and should be confirmed by a qualified installer.

Which tool do I need?

Start from your question.

Cooling and heating: BTU, tons and kilowatts

Heating and cooling capacity is measured in BTU per hour, kilowatts or tons. One ton of cooling is 12,000 BTU per hour, and 1 kW is about 3,412 BTU per hour. A bigger room, more windows, more sun or more people need more capacity.

More is not always better. An oversized air conditioner cools quickly, switches off, and removes less moisture, so the room feels damp. An undersized one runs constantly. Furnaces have an efficiency rating, AFUE, which is the share of the fuel that becomes heat, so the input rating must be higher than the heat the house needs. Radiators are sized by watts for each room and their output depends on the water temperature.

Ducts, pumps and friction

Air in ducts and water in pipes lose pressure to friction, and this loss grows quickly with speed. A small duct or pipe that carries a large flow is noisy and wasteful. The duct tool chooses a diameter from the airflow and friction rate. The Hazen-Williams equation estimates head loss for water in a pipe from the flow, diameter, length and pipe roughness.

To size a pump you need the flow you want and the total dynamic head: the height the water must be lifted plus the friction losses. For reference, 1 psi is about 2.31 feet of water and 1 bar is about 10.2 metres.

Volumes: tanks, pools and pipes

Most volumes come from a base area times a depth. A rectangular pool is length × width × average depth. A cylinder tank is π × radius² × height. A cubic foot holds about 7.48 US gallons and a cubic metre holds 1,000 litres. A partly filled tank uses the depth of the water instead of the full height.

Household water, septic and rainwater

A household water tank is sized from the number of people, the daily use each and the days of storage you want, with the next standard tank size. Septic tank sizes are usually set by local regulation from the number of bedrooms or the daily flow, so the tool shows a typical minimum, not a rule for your area.

For rainwater, 1 millimetre of rain on 1 square metre of roof is 1 litre. Multiply the roof area by the rainfall and by a runoff factor, because some water is lost to gutters, splash and evaporation. The tool then shows the tank size needed to cover a number of dry days.

Heating and cooling

Tanks, pools and pipes

Pumps and pressure

Septic and rainwater

Terms explained

BTU
British thermal unit: a unit of heat. BTU per hour measures heating or cooling power.
Ton (cooling)
12,000 BTU per hour of cooling.
AFUE
Annual fuel utilization efficiency: the share of fuel a furnace turns into heat.
Head
Pressure expressed as the height of a water column.
Total dynamic head (TDH)
Lift plus friction loss that a pump has to overcome.
Hazen-Williams
An equation for friction loss in water pipes.
Friction rate
Pressure lost per length of duct, used to size ducts.
Tankless / storage heater
A heater that heats water on demand, or one that keeps a tank hot.
Catchment
The roof area that collects rainwater.
Runoff coefficient
The share of rain that actually reaches the tank.

Common questions

How many BTU do I need to cool a room?

It depends on the floor area, ceiling height, sun, windows and the number of people. Enter the room size in the BTU calculator for a first estimate in BTU, tons and kW.

How many BTU are in a ton of cooling?

12,000 BTU per hour.

Is a bigger air conditioner better?

No. An oversized unit switches on and off often, removes less moisture and wastes energy. Size it to the room.

What size water pump do I need?

You need the flow in litres per minute or gallons per minute and the total dynamic head, which is the lift plus friction losses. The pump tool calculates both.

How many gallons are in a swimming pool?

For a rectangular pool, length × width × average depth in feet × 7.48. The pool tool also handles round and oval shapes and gives litres.

How much rainwater can I collect from my roof?

One millimetre of rain on one square metre gives one litre, before losses. Multiply by the roof area, rainfall and a runoff factor. The tool does this by month.

What size septic tank do I need?

Local rules decide it, usually from the number of bedrooms or the daily wastewater flow. The tool shows a typical minimum for comparison.

Can I rely on these for final installation sizes?

They are planning estimates. Have a qualified installer confirm the sizing for your climate, building and local code.

See all heating, cooling and water tools

Last checked 2026-10-15. Spotted a mistake? Tell us and we will fix it.