How it works
A fertilizer bag shows three numbers, such as 24-0-6. They are the percent of nitrogen (N), phosphate (written P2O5) and potash (written K2O) in the bag by weight. A 40 lb bag of 24-0-6 holds 9.6 lb of nitrogen, no phosphate and 2.4 lb of potash.
Pick how much nitrogen you want to put down. The calculator divides the nitrogen you need by the nitrogen percent on the label to find how much product to spread, then works out the phosphate and potash that come with it, and the number of bags.
The lawn panel takes the area as length and width or as a total in square feet or square metres. The garden and crop panel takes a rate in pounds per acre or kilograms per hectare, which is how soil test reports usually give a nitrogen recommendation, and converts it to product.
Check it by hand: a lawn of 100 by 80 ft is 8,000 sq ft. At 1 lb of nitrogen per 1,000 sq ft you need 8 lb of nitrogen. A 24-0-6 fertilizer is 24% nitrogen, so the product is 8 ÷ 0.24 = 33.3 lb, which is 4.17 lb per 1,000 sq ft. A 40 lb bag holds 40 × 0.24 = 9.6 lb of nitrogen, enough for 9,600 sq ft, so one bag covers this lawn. The last number in 24-0-6 is potash, so 33.3 × 0.06 = 2 lb of K2O goes down as well.
Product = nitrogen needed ÷ (N percent ÷ 100) Nitrogen needed = area in 1,000 sq ft × nitrogen rate per 1,000 sq ft P2O5 applied = product × P2O5 percent ÷ 100, K2O applied = product × K2O percent ÷ 100 Area one bag covers = bag weight × (N percent ÷ 100) ÷ rate × 1,000 sq ft Source: the application rate formula used by the LSU AgCenter, "Calculating Fertilizer Application Rates": the nitrogen rate per 1,000 sq ft divided by the decimal nitrogen percent gives the product per 1,000 sq ft. Kansas State University Extension (MF2916) gives 1 lb of actual nitrogen per 1,000 sq ft as the most common lawn application.
Worked example
A lawn of 100 by 80 feet is 8,000 square feet. To apply 1 lb of nitrogen per 1,000 sq ft you need 8 lb of nitrogen. A 24-0-6 fertilizer is 24% nitrogen, so 1 ÷ 0.24 = 4.17 lb of product per 1,000 sq ft, and 33.3 lb for the whole lawn. That also puts down 2 lb of potash (K2O) and no phosphate.
A 40 lb bag holds 9.6 lb of nitrogen and covers 9,600 square feet at this rate, so one bag is enough.
For crops, 100 lb of nitrogen per acre over 2 acres is 200 lb of nitrogen. Urea (46-0-0) needs 200 ÷ 0.46 = 434.8 lb, which is 217.4 lb per acre, or 9 bags of 50 lb.
Good to know
- The nitrogen rate is yours to choose. 1 lb of nitrogen per 1,000 sq ft is a commonly published turf guideline for one application, and LSU AgCenter describes 0.5 to 1 lb per application. The right amount depends on the grass, the season, the product and your soil, so follow your local extension service and the label.
- Slow-release and fast-release products behave differently. The calculator only does the weight arithmetic and does not tell you how fast the nitrogen reaches the grass.
- Spreader settings are not given here. They differ by spreader make and by product, so use the setting printed on the bag or the spreader maker’s chart, and test on a small area. The product per 1,000 sq ft in the result is the figure to check your spreader against.
- Phosphate is often not needed on established lawns, and some places limit or ban it. Check your soil test and local rules. Fertilizer rules near water also differ by region.
- The crop panel only converts a nitrogen rate you enter into product. It does not decide how much your crop needs.
Questions people ask
How much fertilizer do I need for my lawn?
Divide the pounds of nitrogen you want per 1,000 sq ft by the nitrogen percent of the bag as a decimal. At 1 lb per 1,000 sq ft, a 24-0-6 bag needs about 4.2 lb of product per 1,000 sq ft. Enter your area above for the total.
How much nitrogen per 1,000 square feet is right?
A common single application is 0.5 to 1 lb of nitrogen per 1,000 sq ft. Yearly totals depend on the grass type and the local climate, so check your state’s extension service.
What do the numbers on a fertilizer bag mean?
They are the percent by weight of nitrogen (N), phosphate (P2O5) and potash (K2O). A 24-0-6 bag is 24% nitrogen, no phosphate and 6% potash, and the rest is filler or other material.
How many square feet does a bag of fertilizer cover?
It depends on the nitrogen percent, the bag weight and the rate. A 40 lb bag of 24-0-6 at 1 lb of nitrogen per 1,000 sq ft covers about 9,600 sq ft. The calculator shows the coverage for your bag.
How do I convert pounds per acre to a bag amount?
Use the garden and crop panel. Enter the area, the nitrogen rate from your soil test and the label, and it gives the product per acre or hectare and the bags needed.
Can I use kilograms and square metres?
Yes. Switch the units at the top of either panel. The default metric rate of 5 g of nitrogen per m² is close to 1 lb per 1,000 sq ft.
How much 46-0-0 urea gives 1 lb of nitrogen?
1 ÷ 0.46 = 2.17 lb of urea.
Part of the guide: Garden and lawn calculators: soil, mulch, sod, fertilizer and planting dates