How it works
A beam carries a load across a span. The calculator uses the standard formulas of beam theory for the five most common cases: a beam resting on two supports, with an even load or a point load, and a cantilever fixed at one end. It works out the support reactions, the largest shear force, the largest bending moment, the bending stress and the largest deflection.
The bending moment is the quantity that the beam must resist. For a simply supported beam under an even load it is the load per length times the span squared divided by 8. The stress in the extreme fibre is the moment times the distance from the centre divided by the moment of inertia of the section.
The deflection is how far the beam sags. It depends on the load, on the span to the third or fourth power, and on the stiffness of the beam, which is the modulus of elasticity of the material times the moment of inertia of the section. A deeper section is far stiffer than a wide one, since the depth enters the moment of inertia as a cube.
The span to deflection ratio helps to judge the result. Common limits for floors are span ÷ 360 where the finish can crack, and span ÷ 240 for roofs. Each building code sets its own limits, so check yours.
Check it by hand: a 12 ft timber beam, 1.5 by 7.25 in, carries 100 lb per ft. Each support takes 100 × 12 ÷ 2 = 600 lb and the largest moment is 100 × 12² ÷ 8 = 1,800 lb·ft. The moment of inertia is 1.5 × 7.25³ ÷ 12 = 47.63 in⁴, and the section modulus is 1.5 × 7.25² ÷ 6 = 13.14 in³, so the stress is 1,800 × 12 ÷ 13.14 = 1,644 psi. With E = 10 GPa = 1,450,377 psi, the deflection is 5 × (100 ÷ 12) × 144⁴ ÷ (384 × 1,450,377 × 47.63) = 0.675 in, which is 144 ÷ 0.675 = span ÷ 213.
Simply supported, even load w: M = wL² ÷ 8 V = wL ÷ 2 δ = 5wL⁴ ÷ (384 EI) Simply supported, centre load P: M = PL ÷ 4 δ = PL³ ÷ (48 EI) Simply supported, load P at distance a (b = L − a): M = Pab ÷ L Cantilever, even load w: M = wL² ÷ 2 δ = wL⁴ ÷ (8 EI) Cantilever, end load P: M = PL δ = PL³ ÷ (3 EI) Stress = M × c ÷ I Rectangle: I = b × h³ ÷ 12
Worked example
A timber beam of 100 mm by 200 mm spans 4 metres and carries 5 kN per metre. The moment is 5 × 4² ÷ 8 = 10 kN·m, and each support carries 10 kN.
With I = 100 × 200³ ÷ 12 = 6.667 × 10⁷ mm⁴ and E = 10 GPa, the deflection is 5 × 5 × 4⁴ × 10¹² ÷ (384 × 10,000 × 6.667 × 10⁷) = 25 mm, which is span ÷ 160. The stress is 10 × 10⁶ × 100 ÷ 6.667 × 10⁷ = 15 MPa.
Good to know
- The formulas are for a straight beam of one section with a constant stiffness, loaded in its strong direction. They do not cover several loads at once, continuous beams over three or more supports, or beams fixed at both ends.
- The weight of the beam is not added for you. Include it in the load per length if it is significant, which it is for long steel and concrete beams.
- The calculator does not check shear stress, lateral buckling, bearing, or the strength of the material. A structural engineer must design any beam that carries a floor, a roof or people.
- Timber, in particular, varies by species, grade and moisture. The 10 GPa used here is only a typical figure.
Questions people ask
What is the bending moment of a simply supported beam?
For an even load w over a span L it is wL² ÷ 8, and for a point load P in the middle it is PL ÷ 4. The largest moment sits in the middle of the span.
How do I calculate beam deflection?
For a simply supported beam with an even load, it is 5wL⁴ ÷ (384EI). E is the modulus of elasticity of the material and I is the moment of inertia of the section. Enter your values above and the calculator does the rest.
What is the difference between a simply supported beam and a cantilever?
A simply supported beam rests on two supports and can turn freely at the ends. A cantilever is fixed at one end and free at the other, like a balcony slab or a diving board. A cantilever of the same span has much larger moments and deflections.
What is an acceptable deflection for a beam?
Floors are commonly limited to span ÷ 360 under live load, and roofs to span ÷ 240. Your building code gives the exact limits.
How do I find the bending stress in a beam?
Divide the bending moment by the section modulus. For a rectangle the section modulus is b × h² ÷ 6, so a 1.5 by 7.25 in board with a moment of 1,800 lb·ft has 1,800 × 12 ÷ 13.14 = 1,644 psi.
Part of the guide: Roof, stair, deck and structure calculators