Why use our Baseboard Calculator?
- Cost breakdown, not just a length Material, labor, paint and nails, shown as a low to high range with the total and the cost per foot.
- US regional pricing Pick Southeast, Midwest, West or Northeast to move the planning prices, or type your own price for any line.
- Interactive miter diagram Type the corner angle and the diagram and the saw setting update, from a square corner to a bay window.
- A cut list for every board See which wall piece comes from which board and how much scrap is left, so you buy the right number.
- Several rooms in one estimate Each room has its own doors and waste factor, and the rooms share boards.
- Five trim types Baseboard, crown, chair rail, shoe molding and casing, each with its own door logic.
- Feet, inches and fractions Type 12' 6", 12 1/2 or 12.5. Metric works too.
- English, Hindi and Urdu Every label, error and step is translated, and the page flips to right to left in Urdu.
- No ads, no signup, no limits Your numbers stay in your browser.
How to use the Baseboard Calculator
Pick US or metric units, the trim and what you know: the size of a room, a wall run you measured, or several rooms. Type sizes in feet and inches, such as 14, 12' 6" or 12 1/2. The results update as you type, so there is no Calculate button.
Enter the doors and any other gap with no trim, such as a closet or built-in. A standard US interior door is 36 in wide. Baseboard, shoe molding and chair rail stop at a door, so its width comes off the run. Crown runs over doorways, so nothing comes off. Casing is measured round each opening instead, up both sides and across the top.
The waste factor is added room by room: 10% for a simple room, 15% for a complex one, 20% for an intricate one. The run with waste is divided by the board length and rounded up. The cut list then shows how to cut every board from your wall pieces, with the scrap left on each, and the calculator buys whichever count is higher.
Material, labor, paint and nails are priced as a range. MDF, pine, oak and PVC have planning prices per foot, which the region multiplies, from 0.85 in the Southeast to 1.25 in the Northeast. Type your own price to fix a line. My own planning figures cover paint and nails and are written in the working. Solid wood moves with humidity, as the «USDA» Forest Products Laboratory «Wood Handbook» explains, so let it sit in the room before you fix it.
For a corner, type the angle between the two walls. The saw setting for each piece is (180° − angle) ÷ 2, which is 45° at a square corner and 22.5° at a 135° bay. Dividing the corner angle by 2 only works at 90°. Check it by hand: a 14 by 12 ft room has a perimeter of 52 ft, one 3 ft door leaves 49 ft, 10% waste makes 53.9 ft, and 12 ft boards give 5 boards.
Perimeter = 2 × (length + width) × number of rooms Net run = perimeter − doors × door width − other gaps (crown: no doors off) Casing run = openings × sides × (2 × height + width) Order length = net run × (1 + waste) Boards = order length ÷ board length, rounded up Miter setting = (180° − corner angle) ÷ 2 Nail spots = net run ÷ stud spacing, rounded up
Worked example: a 12 by 14 ft room with one door
Perimeter = 2 × (12 + 14) = 52 ft. One 36 in door comes off: 1 × 3 = 3 ft. The net run is 52 − 3 = 49 ft.
Add 10% waste: 49 × 1.10 = 53.9 ft. In 12 ft boards that is 53.9 ÷ 12 = 4.49, so 5 boards, which is 60 ft bought.
With MDF typed at $1.20 per foot and labor at $2.50: material 60 × $1.20 = $72, labor 49 × $2.50 = $122.50, so $194.50 before paint and nails. Nails at 16 in spacing: 49 × 12 ÷ 16 = 36.75, so 37 spots and 74 nails with 2 per stud.
Good to know
- The calculator assumes straight walls and a room that is a rectangle. For other shapes use the known length mode and measure every wall.
- The cut list takes doors off the longest walls first and ignores the length lost to miter cuts. Waste covers that, so use the list as a guide and move the cuts to match your room.
- Prices are 2026 planning ranges, not quotes, and local lumber yards may vary 10 to 25%. The paint and nail figures are my own allowances. Type your own price for any line.
- Inside corners are usually coped, not mitered, which uses a little more trim than a mitered joint. Cut test pieces on scrap before you cut your trim.
Questions people ask
How much baseboard do I need for a room?
Add up every wall, take off the door widths, add 10% for waste and divide by the board length. A 12 by 14 ft room with one door needs 53.9 ft, which is 5 boards of 12 ft.
How many linear feet of baseboard is a 12 by 12 room?
The perimeter is 48 ft. One 3 ft door leaves 45 ft, which is 49.5 ft with 10% waste. That is 5 boards of 12 ft.
What is the miter angle for baseboard?
At a 90° corner each piece is cut at 45°. For any corner the saw setting is (180° − the corner angle) ÷ 2, so a 135° corner is cut at 22.5°. Inside corners are usually coped instead.
Do I take doors off crown molding?
No. Crown runs along the ceiling over every doorway. Baseboard, shoe molding and chair rail stop at the door, so the door width comes off.
How much does it cost to install baseboard per foot?
For primed MDF the planning ranges used here are $0.70 to $1.50 for material and $1.50 to $3.00 for labor, so about $2.20 to $4.50 per foot before paint. Oak runs higher, and the region and your own quote change it.
How to Measure Baseboard
Measure each wall along the floor from corner to corner, in feet and inches, and round up to the next inch. Where there is a door casing, measure to the casing, because the baseboard stops there.
Add the walls, or for a rectangular room use 2 × (length + width). Write down the doors and any closet, built-in or fireplace with no trim, and take their widths off.
For a bay or an angled wall, measure each wall on its own, note the angle between them and type it in the miter diagram. Then add your waste factor and divide by the board length.
More worked examples
12 by 12 bedroom with one door: net run 45 ft, 49.5 ft with 10% waste, 5 boards of 12 ft. At $1.20 and $2.50 that is $72 for material and $112.50 for labor.
15 by 20 living room with two doors: perimeter 70 ft, doors 6 ft, net run 64 ft, 70.4 ft with waste, 6 boards. $86.40 for material and $160 for labor at the same prices.
Whole house, two 12 by 12 bedrooms, one 12 by 14 bedroom, a 15 by 20 living room and a 12 by 14 kitchen: net run 249 ft, 273.9 ft with waste, about 23 boards of 12 ft, and about $954 for material and labor at the same prices.
Part of the guide: Building material calculators: concrete, blocks, bricks, flooring and more